-- MarkWard - 23 Jan 2017


  • Reorganised electronics cabinet to lift potentially delicate electronics off of the floor.
    • Pumping station and penning gauge readout now on a new bottom shelf, interactions with these objects are minimal
    • NIM crate has been moved to the top, this keeps loose cables away from peoples feet!
  • During testing of several power supplies for the Anode, the NIM crate is found to have a faulty -24 volt rail. All other rails appear to be fine within norms, but -24 volt rail reads as approximately 14 volts. This causes problems with anything using -24V and in the case of the power supplies tested, severly limits their output to roughly 300V.
  • Found a power supply with an independant power source, bringing the total to two
  • Found a leak on the atmospheric pressure gauge, it was a little bit more than hand tight, with a single loop of teflon.
  • Leak rate reduced by an order of magnitude after fix, gauge readings appear slightly different during pump down, the gauge looks ok down to approximately 40torr rather than 80. Issue likely being the leak causing local pressure
  • 10^4 range leaks are still pretty poor, BUT can actually indicate virtual leaks or heavy out gassing. Rate of rise measurements become very difficult unless a vessel has been previously baked or pumped down for a long period
  • Less worried the vessel is leaking.
  • Leak_rate.png


  • Floor load testing still to be determined
    • Hole in the floor has been filled with what looks like concrete
    • Items from the hallway have been moved into the lab, couple of crates and boxes plus tables... I suspect these are not perminent features, and were moved for the open day tour. Will confirm with Andy.
    • Andy Reports 24/01/2017 that there is still no full report to the department from the structural engineers, but, the company has been contracted to do the required work on the floor sometime next week... ? Plating? coating? Unknown ?!?
  • Items to Sam at Cryovac;
    • Requested information regarding burst disk part numbers so i can look at tollerances (how Close to 5 bar can we go)
    • Requested information regarding part numbers of components such as regulators
        • Regulators wont have valves on them, can have them if we want intention was to have the solenoids do that work.
        • I agree with this, we can do what we want without them and having just the valve on the bottle to protect the system.
    • Requested information regarding a removable line between the gas manifold and the gas inlet to the chamber. (for later additions)
        • Request made and will be updated on the P&ID
    • Requested information regarding full platform elivation (hand cranked or electrical) for the chamber such that it can be built for 1.3m height but aligned to the beam at 1.7, parrallel to this (Zach) investigate options for elivation changes at CERN
      • Looks like we have a solution of using 800mm and 400mm blocks to build a platform.
      • Michael Jaekel said no problem in getting the correct elevation, only we probably wouldnt be able to move things much once we are up there. Which I think sounds fairly normal.
      • Most likely revert back to our original height.

Topic attachments
I Attachment History Action Size Date Who Comment
PNGpng Leak_rate.png r1 manage 38.8 K 23 Jan 2017 - 11:30 MarkWard  
PDFpdf R.1.05.01_Insert_Type_Holders.pdf r1 manage 402.8 K 25 Jan 2017 - 10:22 MarkWard  
PDFpdf R.1.37.01_Axius.pdf r1 manage 673.1 K 25 Jan 2017 - 10:22 MarkWard  

This topic: Public > UserList > MarkWard > MWardWorkDiary2017W4
Topic revision: r5 - 25 Jan 2017 - MarkWard
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2022 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding RHUL Physics Department TWiki? Send feedback